Author Topic: Engine trouble shooting  (Read 124 times)

Offline Isotope

  • Donor 2026
  • *
  • Posts: 71
  • Total likes: 102
  • WEB-14
  • OS:
  • Mac OS X Mac OS X
  • Browser:
  • Safari 27.2 Safari 27.2
  • Eagle Type: LEXL
Engine trouble shooting
« on: November 19, 2026, 05:16:06 AM »
Vanguard 23 HP / NIBBI PE30 Carburetor Troubleshooting Update

Still trying to figure out my RPM problem on my stock 23 HP Vanguard with a NIBBI PE30, Bandit 1.68:1 redrive, and 60.25” Ultra-Prop.

My latest test was with a #145 main jet, needle in the middle position, and float height at 19 mm.

On the first pull, the engine reached approximately 4,500 RPM and held for about 10 seconds before smoothly dropping to around 3,900 RPM, where it stayed. After idling a few minutes, I repeated the test and got about 8 seconds at 4,500 before the same drop. The engine runs smoothly throughout.

Here’s what I’ve checked so far:

* Tested main jets from #130 through #145. Larger jets improved peak RPM but haven’t eliminated the drop.
* Verified the throttle slide opens fully.
* Measured over 16 oz of fuel flow in 30 seconds at the carburetor.
* Tested fuel flow through the float needle valve at approximately 16 oz/minute.
* Used a clear tube to monitor float-bowl fuel level while running. The level stayed steady even during the RPM drop.
* Tested with the fuel tank cap completely removed to eliminate tank venting problems.
* Installed inline spark testers on both cylinders. Both showed steady spark throughout the RPM drop.

I also discovered intake leaks around my homemade adapter flange. I traced a possible leak path to the mounting bolt holes, which are threaded all the way into the intake passage. I’ve now resealed the flange and bolt threads with MotoSeal, but haven’t tested the latest repair yet.

I’m beginning to run out of ideas. The biggest mystery is why it will hold 4,500 RPM briefly, then settle at 3,900 until I let it idle and try again. See attached video. 

Any thoughts on what could cause this?

https://youtu.be/X2YxVhOayuI?si=vuZpMvspAW32O2eQ


Offline Jaggedscars

  • Jr. Member
  • **
  • Posts: 11
  • Total likes: 9
  • New Member
  • OS:
  • Windows NT 10.0 Windows NT 10.0
  • Browser:
  • Chrome 157.0.0.0 Chrome 157.0.0.0
  • Eagle Type: LE XL
Re: Engine trouble shooting
« Reply #1 on: November 20, 2026, 07:41:34 AM »
Hey, good morning!

Does the RPM drop only on initial startup and first pull, or does it do it each time you pull and return to idle? Not overly familiar with the NIBBI PE30, but does it have bowl vents? Could be a pressure issue inside the bowl and/or something wrong with the carb's metering circuit post bowl & float.

Have you tried another carburetor, possibly a Mikuni VM series or the Keihin PE30? Fully understand the NIBBI is cloned after the Keihin but clones do have some issues.

-Steve

Offline Isotope

  • Donor 2026
  • *
  • Posts: 71
  • Total likes: 102
  • WEB-14
  • OS:
  • Mac OS X Mac OS X
  • Browser:
  • Safari 27.2 Safari 27.2
  • Eagle Type: LEXL
Re: Engine trouble shooting
« Reply #2 on: November 20, 2026, 08:31:14 AM »
RPM drops each time a pull. It does have a vent. My next try is to try and shield the vent. Then try a Nibbi pe26 i have.